Free Shipping on orders over US$39.99 How to make these links

Masterforce 20V Ultra Compact Drill and Impact Driver Combo

Masterforce Packs a Ton of Bang for Your Buck in 20V Ultra Compact Combo

We’ve been talking a lot about Masterforce Boost tools and now it’s time to turn our attention to a smaller subject. We’re teaming up with Menard’s to tell you more about the Masterforce 20V Ultra Compact drill and impact driver combo.

Masterforce Ultra Compact Drill and Impact Driver Combo

The main goal of these tools is to put compact brushless performance in your hands. In general, both of these tools are impressively compact—closer to the size of 12V models than 20V. Even better, there’s legitimately impressive performance under the hood for the size.

Masterforce Ultra Compact Drill Driver

When I opened the box the drill came in, I thought I was looking at a 12V tool. It’s much closer in length to DeWalt’s 12V Xtreme brushless drill than other compact 18V/20V max tools we’ve reviewed, measuring just 5.8 inches from tip to tail.

The weight is low, too. Bare, the drill weighs 2.2 pounds and a 2.0Ah battery bumps it up to 3.3 pounds.

Then there’s the performance. With two speeds available, you can run up to 500 RPM in low gear or 1850 in high. The torque maxes out at 525 in-lbs.

Looking at the Ultra Compact drill compared to Masterforce’s Boost model shows us the difference in both size and performance.

Ultra Compact Boost
Bare Weight 2.2 lbs 3.5 lbs
Length 5.8 in 7.4 in
No-Load Speed 500/1850 RPM 550/2000 RPM
Max Torque 525 in-lbs 800 in-lbs

To put Masterforce’s performance in perspective against other compact drills, Makita’s 18V Sub-Compact XFD15 tops out at 1700 RPM and 350 in-lbs of torque. DeWalt’s 20V Max Atomic DCD708 runs up to 1650 RPM and 575 in-lbs of torque. While DeWalt has a bit more power, those are some big Pro names that Masterforce is legitimately competing with and even beating.

  • Model: Masterforce 8815
  • Power Source: Masterforce FlexPower 20V battery
  • No-Load Speed: 0 – 500/1850 RPM
  • Max Torque: 525 in-lbs
  • Clutch Settings: 17+1
  • Length: 5.8 inches
  • Weight: 2.2 lbs bare, 3.3 lbs with 2.0Ah battery

Masterforce Ultra Compact Impact Driver

Sticking with the compact theme, the impact driver beats the 5-inch mark at 4.9 inches. The weight is very close to the drill driver. The bare tool is 2.3 pounds and a 2.0Ah battery makes it 3.4 pounds. Compare that to the Boost impact driver that’s half a pound heavier and an inch longer.

Like many compact impact drivers, Masterforce’s Ultra Compact model is a single speed with a variable speed trigger for control. Its performance is better than what we expect from the compact class, though.

It has a top speed of 2800 RPM with 3500 IPM to keep your fasteners moving quickly. 1800 in-lbs of torque backs it up and helps it move larger fasteners, such as our GRK Fasteners Rugged Structural Screws.

As you can see in the chart below, you give up a little performance compared to Masterforce’s Boost impact driver but get a much more compact tool.

Ultra Compact Boost
Bare Weight 2.3 lbs 2.8 lbs
Length 4.9 in 5.9 in
Top Speed 2800 RPM 1100/2000/3100 RPM
Impact Rate 3500 IPM 1250/2650/3500 IPM
Max Torque 1800 in-lbs 2000 in-lbs

Looking again at some of the other competition helps us with more context. Makita’s Sub-Compact XDT18 is a little faster with 3000 RPM and 4100 IPM, but it only has 1240 in-lbs of torque. DeWalt’s Atomic DCF885 is similar to Masterforce in speed with 2800 RPM and 3200 IPM. Like Makita, it is well short in the power department with 1400 in-lbs of torque.


  • Model: Masterforce 5764.1
  • Power Source: Masterforce FlexPower 20V battery
  • No-Load Speed: 0 – 2800 RPM
  • Max Torque: 1800 in-lbs
  • Max Impact Rate: 3500 IPM
  • Length: 4.9 inches
  • Weight: 2.3 lbs bare, 3.4 lbs with 2.0Ah battery


You can either one of these Ultra Compact tools for $119.99. For that price, the drill comes with two 2.0Ah batteries and a charger and the impact driver includes one 2.0Ah battery and a charger.

The best value is the combo kit that includes both tools, two 2.0Ah batteries, and a charger for $169.99. Menards frequently runs sales on Masterforce tools, so be on the lookout for even better pricing.

Masterforce’s warranty has you covered for 3 years.

The Bottom Line

The size and weight of the Masterforce Ultra Compact drill and impact driver make these tools a great fit for anyone to use on projects around the home. At the same time, they boast the performance Pros need from their compact tools. Toss in a very reachable price and this is a combo kit that we recommend for both DIYers and value-minded professional tradesmen.

We will be happy to hear your thoughts

Leave a reply