ANCEL PB100 Automotive Circuit Tester Probe Kit Vehicle Diagnostic Test Tool Car Digital Volt Meter 12V 24V Electrical Power AVOmeter AC/DC Voltage Diode Current Resistance Detector

Add your review

74.99

74.99

Add to wishlistAdded to wishlistRemoved from wishlist 0
Add to compare


Price: $74.99
(as of Feb 26,2021 09:03:17 UTC – Details)


Product Description

circuit testercircuit tester

The PB100 automotive circuit tester probe is a must have tool for both professional mechanics and home-use customers who are looking for a fast and accurate solution on 12V – 24V electrical power AVOmeter AC/DC voltage Diode Current Resistance diagnose. Helps you to activate components in the vehicle or W/Ground, read voltage displays red/green polarity LED, tracking, locate short circuits, and bad ground contacts.

PBPB

Product Key Features:

Perform power injection, measuring, ground testing, polarity checking, continuity testing, and component activation;Find short to ground and short to the voltage; Automatically detect the positive, negative and open circuit; 8Amp circuit breaker protection, automatically reset, no button to push; High voltage capability: displays up to 60 volts, resolution of 0.1 volt; AC-RMS, AC peak to peak, frequency and pulse width for signal testing; Comes with an extra 20ft extension cable; Powered by vehicle battery or cigarette lighter; Three additional modes: MIN / MAX / audible monitoring; A large color LCD screen with easy to navigate user menu; Ergonomic housing design with water-resistant, rugged blow molded case, easy to handle and store.

Tester2

Tester2

Tester

Tester

Automotive Circuit Tester2

Automotive Circuit Tester2

Continuity Testing

While the diagnostic tool is in resistance mode, using the probe tip with chassis ground or the auxiliary ground lead, continuity can be tested on wires and components attached or disconnected from the vehicle’s electrical system. When the probe tip is contacting a good ground, the LCD will indicate”0.0Ω” and the green LED will be on. A beep tone will sound.

Activating Components in Your Hand

If the green LED went off at that instant or if the circuit breaker tripped, the tool has overloaded. It may be due to the following reasons:

The contact you are probing is direct ground or negative voltage; The component you are testing is short-circuiting; The component is at a very high current. If the circuit breaker tripped, reset it by waiting for it to cool down(15 sec).

Testing Trailer Lights and Connections

While the automotive tester in DC Voltage mode, clip the auxiliary ground lead to the trailer ground, probe the contacts at the jack and then apply the voltage to the probe tip, lets you check the function and orientation of the connector and trailer lights. If the circuit breaker tripped, that contact is likely a ground. Reset the circuit breaker by letting it cool down for 15 seconds.

power probe

power probe

Tester

Tester

Power Circuit Tester

Power Circuit Tester

Voltage & Polarity Testing

While the electrical probe tester is in DC voltage mode, contact the probe tip to a POSITIVE circuit. The red LED will light, and the LCD displays the voltage with a resolution of 0.1V. A beep tone will sound. If you contact the probe tip to a NEGATIVE circuit, the green led will light, and the LCD displays the voltage with a resolution of 0.1V. A beep tone will sound. If you contact the probe tip to an OPEN circuit, neither of the LED will light.

Activating Components in the Vehicle

Warning: Haphazardly applying the voltage to specific circuits can cause damage to a vehicle’s electronic components. Therefore, it is strongly advised to use the vehicle manufacturer’s schematic and diagnosing procedure while testing.

NOTE: When powering up components, you can increase the life of power switch if you press the switch first, then contact the tip to the component. The racing will take place at the tip instead of the contacts of the switch.

Signal Circuit Testing

Easy to test the sensor. For example, if you suspect there is a problem with your M.A.P.,

Set the tool in AC Voltage mode, using the probe tip with chassis ground or the auxiliary ground lead;Connect vacuum pump to MAP sensor;Contact the probe tip to MAP sensor positive terminal and observe the LCD readings which should be a sine wave in a normal condition;Apply vacuum, release vacuum and observe the LCD readings. If the LCD readings are abnormal, there is a problem with this sensor.

CASECASE

What Do You Get?

1 x PB100 Circuit Probe1 x Extension Cable (20ft)1 x Battery Hookup Clips1 x Cigarette Lighter Adapter1 x Protective Case1 x Probe tip1 x User’s Manual

Test Voltage

12/24V

12V

12V

12V

12V

12/24V

Application

Check Automotive Electrical System

Diagnose Engine System

Check 12V Lead-acid Battery

Check 12V Lead-acid Battery

Test 12V Lead-acid Battery

Test 12/24V Lead-acid Battery

4 Working Modes

DC/AC voltage/Resistance/Diode modes

Read freeze frame data/Live data stream etc.

Test range: 100-2000CCA

Test range: 100-1100CCA

Test range: 100-2000CCA

Test range: 100-2000CCA

Continuity Test/Activate Components/Voltage & Polarity Test

I/M monitor Readiness test/EVAP system test

Crangking test: cranking time, voltage and status

Test regular flooded, AGM flat plate, AGM spiral, GEL battery

Check battery health status

Storage battery test,Maximum load system test

Trailer Lights & Connections/Signal Circuit Test

Display battery voltage/Trip management/Performance test

Charging test: load voltage, unloaded voltage, ripple status, charging system status

Battery standards: CCA, BCI, CA, MCA, JIS, DIN, IEC, EN, SAE, and GB

Cranking test and Charging test

Engine system activation load test, Charging system test

Print Data

Powers by cigarette lighter or car battery

Three alarm tone/Exclusive free App/Vent magnetic mount

Print the last result and voltage waveforms out

Test result: SOH, SOC, CCA value, CCA rating, voltage, internal resistance, etc.

Built-in thermal printer

Internet Update

20 feet extension cord

Designed with polarity reverses connection protection

Battery standards: CCA, BCI, CA, MCA, JIS, DIN, IEC, EN, SAE, and GB.

Battery standards: CCA, BCI, CA, MCA, JIS, DIN, IEC, EN, SAE, and GB.

WIDE APPLICATION – ANCEL PB100 circuit tester is a fast and efficient electrical scanning probe, works on all 12-24V vehicle electrical systems, including cars, boats, trailers, fuel pumps, relays, and more.
A MUST-HAVE TOOL – Designed for voltage & polarity testing, continuity testing, signal circuit testing, supply power/activating components, trailer lights & connections testing. It features red/green polarity indicators, follows & locates short circuits, and checks bad Ground contacts.
4 WORKING MODES – DC Voltage mode for reading the DC voltage with a resolution of 0.1 volts; AC Voltage mode for reading the Max. voltage, the Min. voltage, and frequency; Resistance mode for reading the resistance between the tip and auxiliary ground lead; Diode mode for checking forward bias or reverse bias.
SAFETY & DURABLE – An auto circuit breaker makes this tool very safe and sustainable and its short-circuit protection protects the device from overload. A quick self-test is a must before starting to test a circuit or component, which ensures your tool is in excellent condition.
FRIENDLY DESIGN – A friendly navigate user menu makes it easier to operate, even a beginner without a manual. Built-in 2 headlights allow you to work in the dark area; an extra 20 feet extension cord allows reaching wires in or out of the vehicle or some congested places; a rugged carry case to store the tool whenever.

User Reviews

0.0 out of 5
0
0
0
0
0
Write a review

There are no reviews yet.

Be the first to review “ANCEL PB100 Automotive Circuit Tester Probe Kit Vehicle Diagnostic Test Tool Car Digital Volt Meter 12V 24V Electrical Power AVOmeter AC/DC Voltage Diode Current Resistance Detector”

Your email address will not be published. Required fields are marked *

ANCEL PB100 Automotive Circuit Tester Probe Kit Vehicle Diagnostic Test Tool Car Digital Volt Meter 12V 24V Electrical Power AVOmeter AC/DC Voltage Diode Current Resistance Detector

74.99

ToolKit
Logo
Enable registration in settings - general
Compare items
  • Total (0)
Compare
0